{"product_id":"mounting-plate-for-ego-ch5500-rapid-charger","title":"EGO CH5500 Rapid Charger Wall Plate | Direct Wall Mount","description":"\u003cp\u003e\u003cstrong\u003eWall Mounting Plate for the EGO Rapid Charger: Get It Off the Bench and On to the Wall\u003c\/strong\u003e \u003cbr\u003e\u003cbr\u003eOut of the box, the CH5500 hangs from two small holes in its own housing. EGO rates the combined weight of the charger and a battery at up to 10.6 lbs, and all of it hangs off those two screws. This mounting plate takes over that job. The charger slides down onto the backing plate and seats into place, then reinforcing brackets underneath carry the load from below instead of leaving it to hang.\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"text-decoration: underline;\"\u003e\u003cstrong\u003eBuilt for a Permanent Home\u003c\/strong\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFour Point Mounting: Reinforced screw holes spread the load across four fasteners instead of two, for a mount that stays where you put it.\u003c\/li\u003e\n\u003cli\u003eMounts to Any Wall: Attaches to plywood, studs, or masonry, and to drywall with appropriate anchors rated for the load.\u003c\/li\u003e\n\u003cli\u003eThickened Fastener Bosses: Extra material around every screw hole so the plate does not crush, deform, or pull through over time.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan style=\"text-decoration: underline;\"\u003eEngineered to Carry the Weight\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlide On and Seated: The charger slides straight down onto the backing plate and locks into position. No adapters, no fiddling, no zip ties.\u003c\/li\u003e\n\u003cli\u003eSupported From Underneath: Reinforcing brackets sit beneath the charger and carry the load in compression, which is exactly where plastic is strongest.\u003c\/li\u003e\n\u003cli\u003eReady for the Heaviest Packs: EGO normally rates a loaded charger and battery at up to 10.6 lbs, this is designed to take well over double that. This plate is built and braced to carry it without sag or creep.\u003c\/li\u003e\n\u003cli\u003eTough Construction: Printed in ABS, a durable engineering-grade plastic that holds up to demanding garage, workshop, shed, and contractor trailer conditions.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan style=\"text-decoration: underline;\"\u003eKey Benefits\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eReclaim Your Bench: A charger and a battery take up real estate you would rather use for work. Put them on the wall and get the surface back.\u003c\/li\u003e\n\u003cli\u003eStop Wondering If It Will Hold: Four fasteners and a supported base take the guesswork out of hanging ten pounds on your wall.\u003c\/li\u003e\n\u003cli\u003eCharge Where You Store: Set up your charging station right next to your battery mounts so everything lives in one place.\u003c\/li\u003e\n\u003cli\u003eClean, Finished Look: A charger sitting square and level on a proper plate looks like it belongs there, because it does.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan style=\"text-decoration: underline;\"\u003eFitment\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e EGO Power+ rapid chargers — CH5500, CH5500A\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDoes not fit:\u003c\/strong\u003e CH2100 \/ CH3200 standard chargers.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan style=\"text-decoration: underline;\"\u003eBuilt from Professional Grade ABS, Not hobbyist PLA or PETG\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePrinted in \u003cstrong\u003eABS\u003c\/strong\u003e, the engineering thermoplastic used for power tool housings. It stays rigid when it gets hot.\u003c\/li\u003e\n\u003cli\u003eMost 3D printed mounts sold today are \u003cstrong\u003ePETG\u003c\/strong\u003e, a hobby-grade filament. In a hot garage, shed, or trailer, PETG softens under the sustained weight of a hanging tool.\u003c\/li\u003e\n\u003cli\u003eThe failure is quiet. Nothing cracks and nothing snaps, so you get no warning — you just walk in one day and find your trimmer on the concrete.\u003c\/li\u003e\n\u003cli\u003eABS is what you use when the tool on the hook costs more than the hook.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e* Mounting screws and wall anchors are not included. Select fasteners rated for your wall type and for the combined weight of the charger and battery. \u003cbr\u003e** Mount is not an EGO product and PartForge is not affiliated with, endorsed by, or sponsored by EGO. The charger and batteries are shown for demonstration purposes only and are not included.\u003c\/p\u003e","brand":"PartForge","offers":[{"title":"Default Title","offer_id":48202846142722,"sku":"MNT-EGO-C55-FWM-001","price":19.98,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0812\/4484\/8386\/files\/IMG_2863_ProductStaging.png?v=1784898377","url":"https:\/\/www.partforgeusa.com\/products\/mounting-plate-for-ego-ch5500-rapid-charger","provider":"PartForge","version":"1.0","type":"link"}